About

Weld More – Grind Less

My bad welding pales in comparison to my horrible fit-up skills. I launched Weldables to help other welders like me achieve perfect fit-ups, aligned with slots and tabs, or hole and pins – because everyone knows that a fitter is always more expensive that a welder… and that a good fitup, makes for an easy weld!

Mission Statement: Weldables sells pre-cut metal in flat packed, shippable, unassembled, Ready to Weld kits for industry, homeowners, and hobbyists to assemble and weld themselves, utilizing interlocking “Slot and Tab” or “Hole and Pin” fit-ups at intersections for fixtureless welding – Assembled like a life-sized LEGO® set – no jig required!

Vision: To be the leading material supplier known for improving efficiency of welded assemblies.

*Please note that the terms of our website (including safety and warnings) are written in English and to the extent any translated version of the Terms conflicts with the English version, the English version controls.

*Please see our page on Material Condition – so you know what to expect when your material arrives*

DISCLAIMER: Weldables Inc sells material only. All of our materials must be welded, and / or assembled by the purchaser (or end user). Purchaser (or end user) welding skills, welding techniques, welding procedures, tools, equipment, equipment settings, welding design, competent mechanical ability, and assembly experience are the responsibility of the purchaser (or end user) and are beyond our control. Therefore, Weldables Inc. disclaims all warranty and liability for damage or injury that may result from the purchaser’s (end user’s) welded and/or assembled product. By purchasing our material, you understand and agree to this disclaimer. By purchasing our material, you also agree that our materials are not rated for use as safety devices, nor for assemblies used on public roads, nor for overhead lifting, (nor over any part of the body), nor in any circumstance that could cause property damage or bodily injury.
SAFETY FIRST! Purchaser (or end user) agrees to abide by all safety rules for welding and general construction. End user must use Personal Protection Equipment rated for welding and construction purposes. A good review for welder safety can be found here from the American Welding Society: http://www.aws.org/standards/page/safety-health-fact-sheets

*BY PURCHASING OUR MATERIAL KITS, YOU AGREE THAT THEY WILL BE WELDED BY A QUALIFIED WELDER, FOLLOWING A WELDING PROCEDURE SPECIFICATION (WPS) ACCORDING TO AWS D1.1 WELDING CODE STANDARDS – OR EQUIVALENT. YOU ALSO AGREE TO THE SAFETY WARNINGS AND SAFE USE, AS LISTED IN THE MATERIAL DESCRIPTIONS AND ON OUR ABOUT PAGE. UNDER NO CIRCUMSTANCE SHOULD ANY OF OUR MATERIAL KITS NOR THE END USER WELDED ASSEMBLIES BE USED AS SAFETY DEVICES, OR IN ANY APPLICATION WHERE A FAILURE MAY RESULT IN BODILY INJURY OR PROPERTY DAMAGE!

NEVER USE OUR KITS FOR OVERHEAD LIFTING OR OVERHEAD SUPPORT!

WARNING & SAFE USE: Our material kits and the end user welded assemblies are not intended for use by persons (including children and persons under the influence of drugs or alcohol) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge. DO NOT USE OUR MATERIAL KITS NOR THE END USER WELDED ASSEMBLIES FOR OVERHEAD LIFTING OR OVERHEAD SUPPORT. DO NOT EXCEED THE WORKING LOAD LIMITS. OUR MATERIAL KITS AND THE END USER WELDED ASSEMBLIES ARE NOT INTENDED FOR USE AS SAFETY DEVICES, OR IN ANY APPLICATION WHERE A FAILURE MAY RESULT IN BODILY INJURY OR PROPERTY DAMAGE. CRITICAL LOADS MUST BE UNIFORMLY DISTRIBUTED ACROSS SUPPORTING SURFACES. LOADS MUST BE STABLE. DO NOT USE ON SLIPPERY SURFACES. USE ONLY ON LEVEL SURFACES. DO NOT USE MATERIALS IF CRACKED OR DAMAGED. DO NOT STAND OR SIT ON THE MATERIAL KITS NOR THE END USER WELDED ASSEMBLIES. DO NOT USE AS SCAFFOLDING. DO NOT USE AS A STEP LADDER OR STANDING PLATFORM. DO NOT SLIDE, PUSH, PULL, LIFT OR ANYWAY MOVE THE MATERIAL KITS NOR THE END USER WELDED ASSEMBLIES WHEN WEIGHT IS ON TOP. DO NOT OVERLOAD. USE ONLY ON FLAT, DRY, HARD AND LEVEL SURFACE. FLOOR SURFACE SHOULD BE CLEAR OF DEBRIS AND CLUTTER.

* The use of our kits are subject to certain hazards that cannot be met by mechanical means, but only by the exercise of intelligence, care and common sense. Serious hazards are: Overloading, dropping or slipping of the load caused by improper rigging, obstruction to free passage of the load, bending, twisting and the use of damaged components. Any such abuse or misuse may cause injury or property damage for which the manufacturer accepts no liability

AS IS WARRANTY: our material kits are provided “AS IS” without warranty of any kind. Weldables Inc. hereby disclaims any and all warranties, expressed or implied, with regard to our material kits including, without limitation, warranties of merchantability, fitness for a particular purpose and non-infringement. Purchaser’s sole and exclusive remedy, and Weldable Inc.’s entire liability, shall be limited to refund of the purchase price, only upon return of the material kit, its original packaging, in salable condition, and proof of purchase to the address on our contact webpage. Weldables Inc. shall in no event be liable for any indirect, incidental or consequential damages whatsoever arising from the sale or use of our material kits.

BY PURCHASING OUR MATERIAL KITS, YOU AGREE THAT THEY WILL BE WELDED BY A QUALIFIED WELDER, FOLLOWING A WELDING PROCEDURE SPECIFICATION (WPS) ACCORDING TO AWS D1.1 WELDING CODE STANDARDS – OR EQUIVALENT. Weldables Inc. does not provide completed welded assemblies and therefore can not guarantee the final outcome of the “end user welded” products. Weldables is providing the material only. WELDABLES SELLS THIS MATERIAL “AS IS”

“Uniformly-Distributed-Load” means that all of the weight is distributed evenly across the supporting surface – AND NOT CONCENTRATED IN ONE OR MORE AREAS OF THE SURFACE.

NOTE: WELDING PROCEDURE SPECIFICATION (WPS) AND THE DESIGN OF WELDED CONNECTIONS – (Purchaser / End User Responsibility)

The end user / purchaser is ultimately responsible for coming up with or using a Welding Procedure Specification to be used in welding and assembly of our material kits. Welding Procedure Specifications should demonstrate full and complete information regarding location, type, size, and extent of all welds and shall be clearly shown on the drawings.

Weld bead penetration should be indicated. Also note that certain welding sequences and techniques can affect joints and make then susceptible to warpage, distortion, and shrinkage stresses. Therefore, to minimize shrinkage stresses and distortion it’s especially important that the welding sequence and technique be carefully noted and followed.

Welding shall be in accordance with AWS D1.1 or equivalent (or as applicable for the end user’s design requirements). Welds shall be as specified by the Purchaser / End User / Designer. Provide welding special inspection as required by local or industry specific codes.

Leave a Reply

Your email address will not be published. Required fields are marked *